Dental Cordless Wireless LED Curing Light Lamp Teeth Whitening Blue Lights Power

Description

Description
D2:
Introduction:
Thank you for choosing D2 curing light unit．This unit is a kind of new type curing device which using the high-power, high—brilliance, pure blue light LED as light source，with the advance light guide rod．
1.The unit is using the LED which has 430—485nm wavelength in the dental operation．
2. LED Screen, easy to check.
3. When works it generates little heat and does not need
a fans to cool the unit ,noiseless and without vibration，
4. This unit has a Li large capacity battery，it can be used for a long one with full charging.
5.Because there are no cables connect to the handpiece，it could be used very conveniently．
6. Three Mode:
“01”Mode：Gradually mode
“02”Mode：Flashing mode．
“03”Mode：All light mode．
7. Automatically power down：when the unit is standby and
without pressing button for 8 minutes，this unit will be turned
off automatically．
8. low battery alert：Every time open the unit power if the voltage of the battery is lower than the set point, this unit will be alarm.
Specification:
Size…………………．dia 22*175mm(unit)
Safety kind……………Ordinary type B．non—continuous service Ip40．Class 2．
Input voltage……………100—240V,50-60HZ(we will send the correct plug according to buyer’s location)
Battery capacity………………·2000Mah
Wavelength………430-485nm
Intensity-………
5W≥1800mw／cm2
Solidification effect……20s，>3mm (3W) ，6s，3mm (10W)
Packing List:
1Main unit…………………l set
2Light guide rod…………1 pc
3 Battery………………………1 Pc
4 Charger……………………1 set
5 Adaptor…………………… 1 pc
6 Light cover plate……… 1 pc
7 User manual (English)…………………1 pc
T4:
T4 curing light adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time. This curing light with adjustable working time, working time visual, curing efficiency higher and intelligent zed charging stand. We have two colors for your reference.
Feature:
Four modes of working time: 10,20,30,40 seconds
Working modes: Full power
The battery can be replaced
The optical fiber can be autoclaved to the high temperature and pressure.
Automatic shut down function(120s no any operation)
Technical Specifications:
Power supply:``````````````````````````````````````````````Rechargeable Lithium battery
Battery voltage and capacity: ``````````````````````` 4.2V/2000mAh
Input of adapter:``````````````````````````````````````````100V to 240V~50Hz/60Hz
Light intensity: ````````````````````````````````` ```````````1400MW/CM2
Light source:
A. blue ray
B. wave length:420nm-480nm
Working condition:
A.environment temperature:````````````````````````````````5℃ to 40℃
B.relative humidity:`````````````````````````````````````````````≤80%
Consumption power：````````````````````````≤8W
protection type against electrical shock:````````````````Class Ⅱ
Protection against electrical shock:```````````````````````type B
Packing list:
1. Main unit x 1
2. Optical fiber x 1
3. Light hood x 1
4. Adaptor x 1
TH:
Optimum polymerization is an important requirement for all light-cured material in order to consistently produce high-quality restorations.
The polymerization light selected also plays a decisive role in this respect .Therefore ,we would like to thank you for having purchased Xlite.
Xlite is a high-quality medical device which has been designed according to the latest standard of science and technology in compliance with the relevant industry standards.
There operating instructions will help you safely start up the device, make full use of its capabilities and ensure a long service life.
Precaution
:
The Xlite Ⅱ curing light intensity can result in build up of heat around the tip of the device .
Prospective users are asked to take extra precaution to prevent direct contact with the skin ,oral mucous membrane ,or the gingiva during use.
The device is for professional use only.
Product Specifications:
Product Specifications:
Light source
Broad spectral LED
Wavelength range
385-515 nm
Light intensity
1300mW/cm
²
Battery
Lithium-ion battery
Total rentime with fully charged battery
30 min
Dimensions
Handpiece: maxØ25.5mm
×
220mm
Charger base:Ø65mm
×
23mm
Weight
Handpiece 93G Charger base 190g
Input Voltage
100-240VAC,50-60HZ
Output Voltage
5vdc/1a
Time to charge Discharged Battery
Max 5 hours
Operating Temperature
+10
℃
- +35
℃ （
+50
℉
- +70
℉）
Operating relative humidity
30% --- 75%
Operating environment pressure
700hpa-1060hpa
Safety:
1. The xlite Curing Light must be used in strict accordance with the following operating instructions. Discus Dental
accepts no liability for any damage resulting from the use of this unit for any other purpose .
2. Prior to start-up of Xlite curing light make sure that the operating voltage started on the rating plate is compatible
with the available mains voltage . Operation of the unit at a different voltage may damage the unit.
3.
Exposure must be restricted to the area of the oral cavity in which clinical treatment is intended.
4.
Use only chargers and adapters supplied by Shenghua Industry. The use of third part chargers and/or power adapter
may result in damage to the unit and my be hazardous to users/patients.
5.
Do not allow cleaning agents to directly enter the unit as this may cause premature failure . See maintenance and care.
6.
Do not use on patients with a history of photo biological conditions including urticarial solaris or erythropoetic protoporphyria
or who are on photosensitizing medications.
7.
Suitable blue-light filtering safety goggles must be worn by patient and dentist during use.
Curing Mode Guide
Mode
Fast mode
Ramping mode
Light intensity
1300mW/cm
²
100 to 1300mW/cm
²
Times
15 sec
20 sec
Curing Mode Swith
Press and hold the switch one sec, light curing unit emit a short beep. And then release. This can be converted from one mode to another mode.
Mode
Fast mode
Ramging
Indicator
Blue LED steady
Blue LED flashing
Charge Status
Status
Low battery
Full
Charging
Indicator
Green LED steady
Green LED off
Green LED flashing
Packing List:
a. Power adapter
b. Curing light unit
c. Charger base
d. Instruction manual
ST1:
Feature:
- 5W power light
- 2 color lights: blue light for solidify resin material, white light is diagnostic function
- Four working models: strong power, low power, flashing, gradually strong
- Solidify time: 5s-40s select
- Wireless, low battery alert, battery can be recharged
- full charging to work for 10 seconds each time can be used continuously for more than 300 times
- Brand new model match light meter
Technology data:
Working voltage: 100-240V 50-60Hz
Wavelength: 420-480 nm
Light power: more than 1500mw/cm2
Capability of battery: 2200mA/h3.7 V
It can solidify 2-3mm deepness in a few seconds
Packing list:
1 Main unit*1
2 Charging base*1
3 AC adaptor*1
4 Light shade*1
5 Light guide* 1
ST2:
Feature:
1. Built-in light meter function
2 Wireless Inductive charging, longer life span
3 Four models to choose (STRONG LOW FLASHING GRADUALLY STRONG)
4 The handle covered by ANS painting
5 Can be used continuously more than 500times
Technology data:
Blue-ray illumination: 5W≥1200Mw/CM2
Capability of battery: 2200mA/h 3.7V
Input Voltage: AC 110-240V 50-60Hz
Wavelength: 420-480nm
Light power: 1200-2000mw/cm2
Solidify depth: 5s/3mm
Time select: 5, 10,15,20,25,30,35,40 seconds
Battery standby time: 90 days
Packing list:
Main unit*1
Charging base*1
AC adaptor*1
Light shade*1
Light guide*1
Whiten tip *1
D8:
Feature
This product is used in fast solidification by lighting dental resin.
It is a new generation of standard developed LED curing light, with humanity intelligent chip,
World advanced high intensity LED light and Li-on rechargeable battery.
It can cure all the dental resin in the market nowadays
Its performance is further surpassing the halogen curing light's, which can solidify 4-5mm deepness in 8 seconds.
Technical parameters
Power voltage:   AC100-240V 50-60Hz
L.E.D Ortho light- super light intensity: 2000mw/cm2
Light guide for fast and powerful curing
exposure times for optimal curing: 8s/ 6s/ 4s
You can select the right time for the different types of material you wish to cure.
Packing list
1. Curing light
2.  High capacitance rechargeable battery
3. Charger
4. Operation manual
3S:
Technical Parameters:
Light Source:
Broad Band LED;
Wavelength Range:
385 - 515 nm;
Light Intensity:
> 2300mW / cm²;
Battery:
Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);
Power Adapter Input Power:
AC 100-240V 50 / 60Hz;
Charging time:  about 45 minutes;
Size:Handle:
Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm (all of the above are the largest size)
Weight:  Handle: 96 grams; Charging seat: 99 grams;
Operating ambient temperature:  + 10℃ - + 40℃(+ 50 °F - + 70°F);
Operating relative humidity:  30% - 75%;
Operating environment pressure:
700hPa - 1060hPa;
Package Contents:
1 × host handle;
1 × charging base;
1 × power adapter;
1 × user manual.
Operation and function description:
The entire handle is only one button, light built-in button.
1. For the first time, charge the light curing handle first. Plug the USB cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally
Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows:
| Emerald Flashing | Battery charging;
| Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode.
2. Working mode selection, by pressing the button for 2 seconds to release to switch the working mode.
| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW / cm².
| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²
3. Turn the light curing lamp on and off, press the button briefly.
4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.
D5/D6:
Features:
1. Brand New High Quality Curing Light.
2. Composes of high power LED, qualified fiber rod.
3. Noiseless; No libration; Generate little heat when working.
4. Low consumption of standby power with thirty days' standby time
5. Large capacity Li-battery can be used for a long one with full charging.
6. Plenty of fiber rods with very reasonable price on sale for your replacement.
7. Wireless/Cordless design without no cable connect to the unit which could be used very conveniently．
8. It adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time.
9. Many brands' resin materials can be cured by this curing-light with optional working modes and lighting times.
Technical:
1. Light source: blue light
2. Wave length: 420nm-480nm
3. Output intensity: 1100-1600mW/cm2; 5W LED
4. Power supply: rechargeable Lithium battery 3.7V/2000mAh
5. Input adapter: 100V to 240V~50Hz/60Hz (Available for global users.)
6. Safety kind: Ordinary type B．non—continuous service Ip40．Class 2．
7. Working condition: environment temperature: 5℃-40℃; relative humidity:≤80%
8. The fiber rod can be autoclaved up to the tempreture134 °C / 273 °F & pressure 0.2Mpa.
9. Build-in light meter within the base
10. Digital LED screen display, clear operation.
11. BEEP at each 5-seconds to indicate remaining curing time
12. Various Curing Time: seven preset curing time 5/10/15/20/25/30/40 seconds.
13. Three Preset Programs:
a. Fast mode: Full power all the time
b. Soft 1 mode: Generally increasing power in first 5 seconds, then full power till the end.
c. Soft 2 mode: Generally increasing power in first 5 seconds, then half power till the end.
14. Full supply of power can satisfy 10-second curing time for 200 times.
15. When running out of the battery, the unit can be operated directly with the switching power adapter.
Packing List:
Main Unit*1
Light Guide*1
Light Board*1
Charging base*1
100v-240v AC Adapter*1
English Operation Manual*1
FDA Statement
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies.
If so, you can bid on this item only if you are an authorized purchaser.
If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
Payment
We accept PayPal payment ONLY, it is easy and safe. Payment should be sent within 7 (SEVEN) days of auction closing. All winning bidders whom won our item, please let me know your contact number after you made the full payment , we need this number to make sure you can receive your item in time, and also for emergency contact consideration.
Feedback
IMPORTANT INFORMATION ON OUR POLICY AND FEEDBACK
Please leave me
FIVE STAR POSITIVE
feedback if you are satisfied with our items.
We try to be fair and accurate with all of our product listings and descriptions. Please read each auction, bid, and sale carefully.
We will appreciate it if you please email us before leaving negative feedback. If there is a problem, we can work together to resolve it. We strive to always be extremely fair and always try to work with reasonable customers.
Negative feedback doesn't go away and should only be left as a last resort! We strive for positive feedback, harmonious relations and even friendships.
We will always make every attempt possible to resolve issues if we made a mistake.(It happens). Please do not assume a mistake is intentional.
Let us know if our service could be better!!
Shipping
International Shipping to worldwide.
Handling within 24 business hours.
Tracking info of your parcel is available.
Returns could be accepted within 60 days after receipt of the item.
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying.
It usually takes 15-45 business days to arrive by economy international shipping and 7-12 business days by express. The following form is for your reference.
Returns
Returns could be accepted within 30 days after receipt of the item
Terms of Sale:
Refund or replacement request is available only the requests within 1 week after parcel received & returning the item as the same condition as received. Please contact us to request a return authorization. Your name, auction number, and reason for return should be included in the email. All items returned must contain all original packaging materials.Please repack the item carefully. Items returned will be tested and a new replacement will be shipped to the buyer immediately when found defective. In the event that a suitable replacement is not available then a refund will be issued. Shipping, handling and insurance fees are non refundable. If the item is found non-defective, the item will be sent back to the buyer at buyer's expense. Items returned without RMA number will be refused and returned to the sender. Buyer is responsible for All Return Postage and Shipping Charges. Buyer is responsible for additional shipping costs for items that are returned refused and / or undeliverable. We do not accept any returns without an authorization number on the box or label it is being returned.
Contact us
We will reply all messages within 24 business hours and we are able to give you a quick response during the duty time. If we are off duty, please kindly be patient and give us a little more time, not just leave the neutral or negative feedback without communication. Every problem will be solved ASAP if you contact us!
Copyright?Dreamland Dental Store,All rights reserved.
FDA for Curing Light:
510(K) Number: K192233
Regulation Number: 21 CFR 872.6070
Product Code: EBZ
FDA for Handpiece:
510(K) Number: K181691
Regulation Number:  872.4200
Classification Product Code: EFB
Subsequent Product Code: EGS
FDA for Scaler:
510(K) Number: K163414
Regulation Number: 872.4850
Product Code: ELC